CGI Bathroom Remodeling Nationwide

CGI Bathroom Remodeling: The Tampa Owner’s Guide

A full CGI bathroom remodel in Tampa typically runs between $9,000 and $28,000 installed, depending on the scope, the materials you select, and whether we’re working with existing plumbing or moving drain lines. We stock and install CGI-compatible showers, tub surrounds, and wall systems, and we can usually have a crew on-site within a week of your written estimate. Most homeowners don’t call us because they woke up wanting a new bathroom. They call because a CGI surround cracked at a seam, water got behind the panel, or the caulk line failed and now the subfloor feels soft underfoot. That’s the reality of bathroom fixtures in Florida: humidity and daily wet-dry cycles are hard on bonded surfaces, and CGI products are no exception. The good news is that a failed CGI panel doesn’t always mean a full gut job. Sometimes it’s a three-day swap. Sometimes it’s more. We’ll tell you which before we ever pick up a tool.

Call (941) 655-9297

Key Takeaways

• Installed CGI bathroom remodels in Tampa run $9,000 – $28,000; smaller fixture replacements start lower.
• We identify your specific CGI model line, match the replacement panel or component, and install it by the book.
• Every job gets a written price before work starts, covered by the 365-Day Done Right Promise.
• Water intrusion behind a failed CGI panel is the single most common repair trigger in Tampa’s climate.

Which CGI Models This Applies To

CGI manufactures bathroom wall systems, tub surrounds, and shower panels across several product lines, and the compatibility details matter more than most homeowners expect. The biggest gotcha we run into on Tampa job sites is panel thickness and lip profile. Older CGI surrounds used a thinner gauge with a shallow overlap at the seams, while newer lines use a deeper interlock that won’t marry up with the older panels. If you’re replacing a single damaged panel, you can’t just grab “a CGI panel” and expect it to seat correctly. You need the series name or the molded stamp on the back of the panel. We read those stamps before we order anything. The second gotcha is drain placement. CGI tub and shower bases are drilled for specific rough-in locations, and Tampa homes from the 1970s and 1980s often sit on slab foundations with drain stubs that don’t match current production. Moving a drain line in a slab is a different job than a panel swap, and we’ll tell you if that’s where your project is headed. Bradford Remodeling Co Tampa is an independent service provider, not affiliated with CGI. We buy from authorized distributors and we match OEM panels when they exist for your series; when they don’t, we’ll say so and give you the aftermarket option with its actual spec, not a sales pitch.

Signs Your CGI Bathroom Remodeling Is Failing

• Caulk line pulling away at the panel seams. This is almost always thermal expansion, not bad caulk. CGI panels expand and contract with Tampa’s temperature swings. When the caulk separates, water finds the gap. Recaulking buys time; if the seam has separated repeatedly, the panel or the substrate behind it has moved and needs a closer look.
• Soft spot or flex in the wallboard behind the surround. This means water has been getting behind the CGI panel for a while. By the time the panel flexes when you press on it, the substrate is compromised. In older Tampa homes with drywall substrate instead of cement board, this is especially common.
• Mold smell that doesn’t go away after cleaning. Mold behind a shower surround is a Florida specialty. The visible panel can look fine while the cavity behind it breeds growth. If you smell it, we need to open the wall and see what’s actually back there.
• Cracked or cloudy panel surface. Aesthetic at first, but cracks become water paths. Clouding usually means the gel coat or clear layer is breaking down from years of hard water and high humidity, which is common all across Tampa, especially on well water.
• Water staining on the ceiling below a second-floor bathroom. This is the alarm bell. By the time water travels through the subfloor and shows up on a downstairs ceiling, the leak has been active for weeks. We trace it, remove the damaged section, and repair the substrate before anything cosmetic goes back up.

Replacement Cost & What’s Included

Here’s the straight number for Tampa: a full CGI bathroom remodel with a new surround or shower system, vanity, fixtures, and finishes runs $9,000 to $28,000. A focused replacement more in line with a tub-to-shower conversion or a single surround swap lands in the $3,500 to $10,000 range. The spread depends on whether we’re reusing plumbing, what the substrate looks like once we open the wall, and what materials you select. You’ll get a written line-item price before any work starts. No numbers that move at the door. That price includes tear-out of the failed section, substrate repair or replacement where needed, the CGI or CGI-compatible panels, installation, waterproofing at every seam and penetration, and haul-away of the old material. Every completed project carries the 365-Day Done Right Promise. If the work fails inside a year, we come back and correct it at no charge. That guarantee is in writing, signed, and in your hand at close-out.

DIY or Call Us?

Here’s the honest split. You can safely check the caulk lines, look for visible cracks, and watch for water stains on the ceiling below. That’s real information and it helps us price the job before we arrive. What you should not do is pry a CGI panel off the wall to “see what’s behind it.” Long before you get the panel off, you’re into the high-tension territory of water lines, and in a lot of Tampa slab homes, the drain connection is rigid PVC cemented into place. One wrong move with a pry bar and a repairable seam crack becomes a plumbing job. The same goes for cutting into the surround with any kind of saw. We’ve lost count of how many times we’ve shown up in Seminole Heights to a homeowner who found a live electrical line right where the old panel was glued. If the panel is cracked, soft, or separating at the seam, call us. We’ll open it with the water off and the scope documented. Straight number, clear scope, no surprises at close-out. Call (941) 655-9297 and we’ll schedule a look.

How much does a CGI bathroom remodel cost in Tampa?

Can a cracked CGI panel be repaired instead of replaced?

It depends on the crack’s location and whether water has gotten behind the panel. Surface cracks in a low-stress area can sometimes be cosmetically repaired, but any crack that flexes or sits at a seam means the panel integrity is gone and we’re replacing it. If we can repair honestly, we’ll price the repair. We won’t band-aid a seam crack and call it done.

How long does a CGI bathroom remodel take?

A single surround or shower replacement typically takes three to five working days from tear-out to a finished, caulked job. A full bathroom remodel with new plumbing locations, tile work, and custom vanity installation runs two to four weeks depending on scope. You’ll have the timeline in writing before we start, along with the price.

Do you stock CGI parts in Tampa or do I have to wait on shipping?

We maintain inventory of common CGI-compatible trims, sealants, and panel adhesives on our trucks, and we source full CGI panels through authorized regional distributors with two to five day delivery to the Tampa area. We’ll confirm the lead time on your specific model before you sign anything. You’ll know the part schedule as part of the written estimate.

Written by Curtis Lane, Owner, Bradford Remodeling Co Tampa at Bradford Remodeling Co Tampa, serving Tampa and nearby areas.