Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Roofing: The Tampa Owner’s Guide
Bradford Remodeling Co Tampa stocks and installs Schluter-compatible roofing components, and most Schluter roofing repairs in Tampa run between $400 and $1,800 installed, depending on the failed part and the substrate condition. Homeowners typically discover the problem after a hard Florida downpour, when water shows up where it shouldn’t, or during a visual inspection when a flashing detail has pulled away from the roof deck. You’ll get a written price before we touch anything, and the work is covered by our 365-Day Done Right Promise.
We’re an independent contractor, not a Schluter affiliate, which means we match parts to your exact system without being tied to a single distribution channel. If a Schluter piece is discontinued or backordered, we’ll tell you that on the first call and give you the aftermarket option with the same spec. No surprises at close-out.
One more thing worth knowing up front: roofing is not the place to save $80 on a knockoff part. We’ll get into that below.
Which Schluter Models This Applies To
Schluter’s roofing line covers edge and penetration details more than full roof systems, and the two series we work with most in Tampa are the Schluter BARA edge profiles and the Schluter TROBA drainage and ventilation mats. BARA profiles come in heights from roughly 4 mm to 10 mm, and the wrong height means water either pools behind the profile or runs over it entirely. TROBA mats vary in thickness and drainage capacity, and the Tampa climate makes the wrong mat a mold invitation.
Here’s the compatibility gotcha most owners hit: Schluter fastening requirements change with the roof substrate. A BARA profile set for a plywood deck is not automatically correct for concrete or single-ply membrane. We check the substrate before we order or pull anything from the truck.
On OEM versus aftermarket: for Schluter edge profiles, we install OEM whenever it’s available. The alloy and coating spec on the original BARA profiles holds up better against Tampa’s salt air and summer UV than most generic aluminum edging we’ve pulled off roofs. For TROBA mat replacements, we’ll use a matched-spec aftermarket option if the Schluter series was discontinued, but only when the drainage rate and compressive strength are equal. We document the brand and model in your written estimate, so you know exactly what’s going on.
Styles & brands we work with
Signs Your Schluter Roofing Is Failing
- Water staining at roof edges or around penetrations. This is the classic BARA failure sign: the profile has pulled up or corroded at a seam, and water is getting under the edge detail instead of shedding past it. By the time you see the stain inside, the substrate has been wet for a while.
- Lifting or curling metal at the drip edge. Tampa’s afternoon thunderstorms pound edge details, and the thermal expansion cycle of aluminum against a hot roof deck eventually works fasteners loose. A lifted edge profile is no longer doing its job.
- Granules accumulating in gutters faster than normal. If your shingle roof is shedding granules at an unusual rate near the edges or penetrations, the Schluter detail may be holding water against the shingle instead of moving it away. Standing water at an edge shortens shingle life fast.
- Musty odor in the attic after heavy rain. A failed TROBA ventilation mat traps moisture against the deck instead of letting it drain and dry. In Florida humidity, that turns into odor quickly, and eventually into deck rot.
- Visible corrosion or pitting on metal profiles. Salt air near Tampa Bay accelerates oxidation on the wrong alloy. Once pitting starts, the profile’s protective layer is gone and the failure is progressive.
Replacement Cost & What’s Included
Schluter roofing part replacement in Tampa runs from $400 to $1,800 installed. A single edge profile replacement on a straight run is at the low end. Replacing a TROBA drainage mat across a roof section, including deck inspection and any substrate repair, pushes toward the high end. If we find deck rot during the job, we price the repair as a separate written line item and get your sign-off before proceeding. You’ll never see a change order we didn’t discuss first.
Every estimate includes the parts, labor, disposal, and our written warranty. We pull a permit when the scope requires one, and we pass inspection before we call the job done. Curtis Lane prices a job once and stands behind the number.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
What you can safely check yourself: visible lifting at edges, signs of corrosion, granules in the gutter, and any daylight showing under a profile. Take photos. That’s genuinely useful when you call us, because it helps us bring the likely parts on the first trip.
What you should not attempt: pulling a profile on a steep roof without proper tie-off, working near the rake edge, or any repair that involves removing shingles or membrane. Tampa roofs are steep enough that a simple edge inspection turns into a fall hazard fast. And fastening a new Schluter profile over a water-damaged substrate just hides the problem until the deck fails. We’ve fixed enough of those to know.
If you’re not sure whether it’s a $400 fix or a $1,800 repair, call us at (941) 655-9297. We’ll look at the photos, tell you what we think, and give you a written price before any work starts.
FAQs
OEM Schluter aluminum edge profiles typically last 15 to 25 years in Tampa, but exposure to salt air near the bay and intense UV can shorten that to 10 to 15 years on some elevations. TROBA mats generally last the life of the roof if they were spec’d correctly for the roof’s drainage load. If your roof is past 15 years old and you’re seeing edge failures, the rest of the detail work is likely approaching replacement too. Call (941) 655-9297 and we’ll give you an honest assessment and a written estimate.
Small, local issues can sometimes be repaired, like resecuring a loose profile with proper fasteners or patching a single seam, but most failures we see in Tampa are progressive corrosion or substrate damage that warrants replacement. A repair that ignores what caused the failure just means a second trip and a second invoice later. We’ll tell you which category yours falls into before quoting anything.
A single edge profile replacement on a straight run is usually a half-day job. A TROBA mat section with substrate repair is typically one to two days depending on the size of the section and Tampa’s weather. We schedule roofing work around the afternoon storm pattern when we can, and we never leave an open deck unprotected overnight.
We keep common Schluter BARA profile heights and fastening hardware on the truck, which means most single-run replacements are done in one visit. Special-order profiles or TROBA mat sections take three to five business days in Tampa. We also stock compatible parts for KraftMaid, Cambria, and Silestone systems for interior work, so if your project spans beyond the roof, we can handle it.
Contact Bradford Remodeling Co Tampa
If your Schluter roofing detail is failing, don’t wait until the next Tampa storm finds the gap. Call (941) 655-9297 and talk to a live person, 24/7. We’ll schedule the inspection, give you a written price, and fix it right the first time. Straight number, clear scope, no surprises at close-out.
Written by Curtis Lane, Owner, Bradford Remodeling Co Tampa at Bradford Remodeling Co Tampa, serving Tampa and nearby areas.
